document number: 81808 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.1, 14-jan-10 1 0.5 a output current igbt and mosfet driver vo3150a vishay semiconductors description the vo3150a consists of a led optically coupled to an integrated circuit with a power output stage. this optocoupler is ideally suited for driving power igbts and mosfets used in motor control inverter applications. the high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. the voltage and current supplied by this optocoupler makes it ideally suited for directly driving igbts with ratings up to 800 v/20 a. for igbts with higher ratings, the vo3150a can be used to drive a discrete power stage which drives the igbt gate. features ? 0.5 a minimum peak output current ? 25 kv/s minimum common mode rejection (cmr) at v cm = 1500 v ?i cc = 2.5 ma maximum supply current ? under voltage lock-out (uvlo) with hysteresis ? wide operating v cc range: 15 v to 32 v ? 0.4 s maximum propagation delay ? industrial temperature range: - 40 c to 110 c ? 0.5 v maximum low level output voltage (v ol ) ? compliant to rohs directive 2002/95/ec applications ? isolated igbt/mosfet gate driver ? ac and brushless dc motor drives ? induction stove top ? industrial inverters ? switch mode power supplies (smps) ? uninterruptible power supplies (ups) agency approvals ? ul - file no. e52744 system code h, double protection ? cul - file no. e52744, equivalent to csa bulletin 5a ? din en 60747-5-5 (vde0884) available with option 1 1 2 3 4 8 7 6 5 shield 20530_1 a c nc nc v o v o v cc v ee v de 19813 ordering information VO3150A-X007T part number package option tape and reel package ul, cul ul, cul, vde dip-8 vo3150a - smd-8, option 7 VO3150A-X007T vo3150a-x017t truth table led v cc - v ee positive going (turn on) v cc - v ee negative going (turn off) v o off 0 v to 32 v 0 v to 32 v low on 0 v to 11 v 0 v to 9.5 v low on 11 v to 13.5 v 9.5 v to 12 v transition on 13.5 v to 32 v 12 v to 32 v high > 0.7 mm 7.62 mm option 7 dip-8
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 81808 2 rev. 1.1, 14-jan-10 vo3150a vishay semiconductors 0.5 a output current igbt and mosfet driver notes (1) stresses in excess of the absolute maximum ratings can cause pe rmanent damage to the device. functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. exposure to abs olute maximum ratings for e xtended periods of the time ca n adversely affect reliability. (2) maximum pulse width = 10 s, maximum duty cycl e = 0.2 %. this value is intended to allow for component tolerances for designs w ith i o peak minimum = 0.5 a. see a pplications section for additional deta ils on limiting i oh peak. (3) refer to reflow profile for soldering conditions for surface mount ed devices (smd). refer to wave profile for soldering conditi ons for through hole devices (dip). absolute maximum ratings (1) (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input input forward current i f 25 ma peak transient input current < 1 s pulse width, 300 pps i f(tran) 1a reverse input voltage v r 5v output power dissipation p diss 45 mw output high peak output current (2) i oh(peak) 0.5 a low peak output current (2) i ol(peak) 0.5 a supply voltage (v cc - v ee )0 to + 35 v output voltage v o(peak) 0 to + v cc v output power dissipation p diss 250 mw optocoupler isolation test voltage (between emitter and detector, climate per din 500414, part 2, nov. 74) t = 1 s v iso 5300 v rms storage temperature range t s - 55 to + 125 c ambient operating temperature range t amb - 40 to + 110 c total power dissipation p tot 295 mw lead solder temperature (3) for 10 s, 1.6 mm be low seating plane t sld 260 c recommended operating condition parameter symbol min. max. unit power supply voltage v cc - v ee 15 32 v input led current (on) i f 716ma input voltage (off) v f(off) - 3 0.8 v operating temperature t amb - 40 + 110 c
document number: 81808 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.1, 14-jan-10 3 vo3150a 0.5 a output current igbt and mosfet driver vishay semiconductors note ? the thermal model is repr esented in the thermal network below. each resistance value given in this model can be used to calcul ate the temperatures at each node for a given operating condition. the thermal resistance from board to ambient will be dependent on th e type of pcb, layout and thickness of copper traces. for a detailed explan ation of the thermal model, please reference vishay's thermal characteristics of optocouplers application note. notes (1) minimum and maximum values were tested over recommended operating conditions (t amb = - 40 c to 110 c, i f(on) = 7 ma to 16 ma, v f(off) = - 3 v to 0.8 v, v cc = 15 v to 32 v, v ee = ground) unless otherwise specified. typical values are characteristics of the device and are the result of engineering evaluations. typical values are for information only and are not part of the testing requirements. al l typical values were measured at t amb = 25 c and with v cc - v ee = 32 v. (2) maximum pulse width = 50 s, maximum duty cycle = 0.5 %. (3) maximum pulse width = 10 s, maximum duty cycle = 0.2 %. this va lue is intended to allow for component tolerances for designs w ith i o peak minimum = 0.5 a. (4) in this test v oh is measured with a dc load current. when driving capacitive loads v oh will approach v cc as i oh approaches zero a. maximum pulse width = 1 ms, maximum duty cycle = 20 %. thermal characteristics parameter symbol value unit led power di ssipation p diss 45 mw output power dissipation p diss 250 mw total power dissipation p tot 285 mw maximum led junction temperature t jmax. 125 c maximum output die j unction temperature t jmax. 125 c thermal resistance, junction emitter to board jeb 169 c/w thermal resistance, junc tion emitter to case jec 192 c/w thermal resistance, juncti on detector to board jdb 82 c/w thermal resistance, junc tion detector to case jdc 80 c/w thermal resistance, j unction emitter to junction detector jed 200 c/w thermal resistance, case to ambient ca 2645 c/w electrical characteristics (1) parameter test condition symbol min. typ. max. unit high level output current i f = 16 ma, r g = 10 , c g = 20 nf, v cc = 15 v, v ee = 0 v i oh (3) 0.5 a low level output current i f = 0 ma, r g = 10 , c g = 20 nf, v cc = 15 v, v ee = 0 v i ol (3) 0.5 a high level output voltage i o = - 100 ma v oh (4) v cc - 4 v cc - 2.1 v low level output voltage i o = 100 ma v ol 0.2 0.5 v high level supply current output open, i f = 7 ma to 16 ma i cch 2.5 ma low level supply current output open, v f = - 3 v to + 0.8 v i ccl 2.5 ma threshold input current low to high i o = 0 ma, v o > 5 v i flh 2.1 5 ma threshold input voltage high to low v fhl 0.8 v input forward voltage i f = 10 ma v f 11.31.6v temperature coefficient of forward voltage i f = 10 ma v f / t a - 1.4 mv/c input reverse breakdown voltage i r = 10 a bv 5v input capacitance f = 1 mhz, v f = 0 v c in 60 pf uvlo threshold v o 5 v v uvlo+ 11 12.6 13.5 v i f = 10 ma v uvlo- 9.5 10.7 12 v uvlo hysteresis uvlo hys 1.9 v t a ca t c t jd t je t b ec eb dc db ba de t a 19996 package
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 81808 4 rev. 1.1, 14-jan-10 vo3150a vishay semiconductors 0.5 a output current igbt and mosfet driver test circuits fig. 1 - i oh test circuit fig. 2 - i ol test circuit fig. 3 - v oh test circuit fig. 4 - v ol test circuit fig. 5 - i flh test circuit fig. 6 - uvlo test circuit 20973_1 1 2 3 4 8 7 6 5 i f = 7 ma to 16 ma v = 15 v to 32 v cc i oh 4 v 0.1 f + + 20975_1 1 2 3 4 8 7 6 5 v cc = 15 v to 32 v i ol 0.1 f 2.5 v + + 20977_1 1 2 3 4 8 7 6 5 v oh 0.1 f 100 ma v cc = 15 v to 32 v i f = 7 ma to 16 ma + 20974_1 0.1 f 100 ma v cc = 15 v to 32 v 1 2 3 8 7 6 5 4 v ol + 20976_1 i f 0.1 f v cc = 15 v to 32 v v o > 5 v 1 2 3 4 8 7 6 5 + 20978 1 2 3 4 8 7 6 5 v o > 5 v 0.1 f v cc i f = 10 ma + switching characteristics parameter test condition symbol min. typ. max. unit propagation delay time to logic low output (1) r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % t phl 0.1 0.4 s propagation delay time to logic high output (1) r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % t plh 0.1 0.4 s pulse width distortion (2) r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % pwd 0.2 s propagation delay difference between any two parts (3) r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % pdd (t phl - t plh ) - 0.35 0.35 s rise time r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % t r 0.1 s fall time r g = 47 , c g = 3 nf, f = 10 khz, duty cycle = 50 % t f 0.1 s
document number: 81808 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.1, 14-jan-10 5 vo3150a 0.5 a output current igbt and mosfet driver vishay semiconductors notes (1) this load condition a pproximates the gate load of a 1200 v/25 a igbt. (2) pulse width distortion (pwd) is defined as |t phl - t plh | for any given device. (3) the difference between t phl and t plh between any two vo3150a parts und er the same test condition. fig. 7 - t plh , t phl , t r and t f test circuit and waveforms notes (1) pins 1 and 4 need to be connected to led common. (2) common mode transient imm unity in the high state is the maximum tolerable |dv cm /dt| of the common mode pulse, v cm , to assure that the output will remain in the high state (i.e., v o > 15 v). (3) common mode transient imm unity in a low state is the maximum tolerable |dv cm /dt| of the common mode pulse, v cm , to assure that the output will remain in a low state (i.e., v o < 1 v). fig. 8 - cmr test circuit and waveforms uvlo turn on delay v o > 5 v, i f = 10 ma t uvlo-on 0.8 s uvlo turn off delay v o > 5 v, i f = 10 ma t uvlo-off 0.6 s common mode transient immunity parameter test condition symbol min. typ. max. unit common mode tr ansient immunity at logic high output (1)(2) t a = 25 c, i f = 10 ma to 16 ma, v cm = 1500 v, v cc = 32 v |cm h |25 35 kv/s common mode tr ansient immunity at logic low output (1)(3) t a = 25 c, v cm = 1500 v, v cc = 32 v, v f = 0 v |cm l |25 35 kv/s switching characteristics parameter test condition symbol min. typ. max. unit 20979_1 1 3 2 4 5 7 6 8 0.1 f i = 7 ma to 16 ma f v = 15 v to 32 v cc 47 500 10 khz 50 % duty cycle i f t r t plh t phl out 90 % 50 % 10 % t f v o 3 nf + + 20980-1 1 3 2 4 5 7 6 8 5 v 0 v 0.1 f a v o v o v = 1500 v cm v = 32 v cc v oh v ol v o switch at a: i f = 10 ma switch at b: i f = 0 ma d v d t d t d t v cm + + + i f = r
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 81808 6 rev. 1.1, 14-jan-10 vo3150a vishay semiconductors 0.5 a output current igbt and mosfet driver note ? as per iec 60747-5-5, 7.4.3.8.1, this optocoupler is suitable fo r safe electrical insu lation only within the safety ratings . compliance with the safety ratings shall be ensured by means of prodective circuits. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 9 - high output voltage drop vs. temperature fig. 10 - high output current vs. temperature fig. 11 - output low voltage vs. temperature fig. 12 - output low current vs. temperature safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classification (according to iec 68 part 1) 40/110/21 comparative tracking index cti 175 399 v iotm 8000 v v iorm 890 v p so 500 mw i si 300 ma t si 175 c creepage distance standard dip-8 7 mm clearance distance standard dip-8 7 mm creepage distance 400 mil dip-8 8 mm clearance distance 400 mil dip-8 8 mm - 3.0 - 2.5 - 2.0 - 1.5 - 1.0 - 0.5 0.0 - 40 - 20 0 20 40 60 80 100 120 temperature (c) v oh - v cc - high output voltage drop (v) i f = 16 ma i out = - 100 ma v cc = 32 v v ee = 0 v 21705-1 - 40 - 20 0 20 40 60 80 100 120 temperature (c) i oh - high output current (a) 21759 0.0 0.5 1.0 1.5 2.0 2.5 i f = 16 ma r g = 10 , c g = 20 nf v cc = 15 v v ee = 0 v 0.00 0.05 0.15 0.25 0.10 0.20 0.30 0.35 - 40 - 20 0 20 40 60 80 100 120 temperature (c) v ol - output low voltage (v) v f(off) = 0.8 v i out = 100 ma v cc = 32 v v ee = 0 v 21707-1 - 40 - 20 0 20 40 60 80 100 temperature (c) i ol - output low current (a) 21760 0.0 0.5 1.0 1.5 2.0 2.5 i f = 0 ma r g = 10 , c g = 20 nf v cc = 15 v v ee = 0 v
document number: 81808 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.1, 14-jan-10 7 vo3150a 0.5 a output current igbt and mosfet driver vishay semiconductors fig. 13 - output low voltage vs. output low current fig. 14 - output high voltage dropvs. output high current fig. 15 - supply current vs. temperature fig. 16 - supply current vs. supply voltage fig. 17 - low to high current threshold vs. temperature fig. 18 - transfer characteristics i ol - output low current (a) v ol - output low voltage (v) 21761 0 0.5 1 1.5 2 - 40 c 25 c 110 c 0.0 0.2 0.4 0.6 0.8 i f = 0 ma v cc = 15 v v ee = 0 v i oh - output high current (a) (v oh - v cc ) output high voltage drop (v) 21762 - 40 c 25 c 110 c - 3 - 2.5 - 2 - 1.5 - 1 0 0.2 0.4 0.6 0.8 i f = 16 ma v cc = 15 v v ee = 0 v 0.0 1.0 1.5 2.0 0.5 2.5 temperature (c) i cc - supply current (ma) - 40 - 20 0 20 40 60 80 100 120 i cch i ccl i f = 16 ma for i cch i f = 0 ma for i ccl v cc = 32 v v ee = 0 v 21710-1 0.0 1.0 1.5 2.0 0.5 2.5 v cc - supply voltage (v) i cc - supply current (ma) 15 20 25 30 35 i cch i ccl i f = 10 ma for i cch i f = 0 ma for i ccl t a = 25 c v ee = 0 v 21711 0.0 2.0 3.0 4.0 1.0 5.0 1.5 2.5 3.5 0.5 4.5 temperature (c) i flh - low to high current threshold (ma) - 40 0 40 80 120 - 20 20 60 100 v cc = 32 v v ee = 0 v output = open 21712-1 0 10 15 20 25 30 5 35 012345 i f - forward led current (ma) v o - output voltage (v) t a = 25 c 21752
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 81808 8 rev. 1.1, 14-jan-10 vo3150a vishay semiconductors 0.5 a output current igbt and mosfet driver fig. 19 - propagation delay vs. supply voltage fig. 20 - propagation delay vs. temperature fig. 21 - propagation delay vs. forward led current fig. 22 - propagation delay vs. series load resistance fig. 23 - propagation delay vs. series load capacitance 100 200 300 400 500 v cc - supply voltage (v) t p - propagation delay (ns) 15 20 25 30 35 t plh t phl i f = 10 ma, t a = 25 c r g = 47 , c g = 3 nf duty cycle = 50 % f = 10 khz 21736 0 100 200 300 400 500 t a - temperature (c) t p - propagation delay (ns) - 40 - 15 10 60 35 85 110 v cc = 32 v, v ee = 0 v i f = 10 ma r g = 47 , c g = 3 nf duty cycle = 50 % f = 10 khz t plh t phl 21737 0 100 200 300 400 500 i f - forward led current (ma) t p - propagation delay (ns) 6 8 10 14 12 16 v cc = 30 v, v ee = 0 v i f = 10 ma, t a = 25 c r g = 47 , c g = 3 nf duty cycle = 50 % f = 10 khz t phl t plh 21738 0 100 200 300 400 500 r g - series load resistance ( ) t p - propagation delay (ns) 01020 40 30 50 t phl t plh v cc = 30 v, v ee = 0 v i f = 10 ma, t a = 25 c c g = 3 nf duty cycle = 50 % f = 10 khz 21739 0 100 200 300 400 500 c g - series load capacitance (nf) t p - propagation delay (ns) 02040 80 60 100 v cc = 30 v, v ee = 0 v i f = 10 ma, t a = 25 c r g = 47 duty cycle = 50 % f = 10 khz t phl t plh 21740
document number: 81808 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.1, 14-jan-10 9 vo3150a 0.5 a output current igbt and mosfet driver vishay semiconductors package dimensions in millimeters package marking note ? vde logo is only marked on option 1 parts. option information is not marked on the part. i178006 pin one id 6.48 6.81 9.63 9.91 0.76 1.14 4 typ. 2.54 typ. 10 3 to 9 7.62 typ. 0.46 0.56 0.2 0.3 2.79 3.30 3.30 3.81 0.51 0.89 5.84 6.35 4 3 2 1 0.79 1.27 5 6 7 8 iso method a 7.62 typ. 0.7 option 7 18450-4 4.6 4.1 8 min. 8.4 min. 10.3 max. 21764-43 vo3150a v yww h 68
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
